Tech Support Forum banner
Status
Not open for further replies.
1 - 5 of 5 Posts

·
In & out... very busy
Joined
·
1,877 Posts
Discussion Starter · #1 ·
Hi again folks. Im back on the overclocking mission again. I tried with the MSI overclocking apps, and found them lacking. Next logical stage is BIOS changes. I have successfully o'cd my 6600GT GPU to 583 clock and 581 memory (525 & 500 stock), so now that is done I would like a slight increase in CPU output. Nothing major, maybe 2.6 0r 2.7ghz.
Any site suggestions or personal experience are greatly appreciated.
 

·
In & out... very busy
Joined
·
1,877 Posts
Discussion Starter · #2 ·


New readouts after mild OC. I only upped the vcore by about 3 or 4 steps (1.38v), memory by 1 or 2. Nothing major, but a noticable increase in ability.
PCWizard benchmarks for anyone whos interested



 

·
In & out... very busy
Joined
·
1,877 Posts
Discussion Starter · #4 ·
Now Im a bit stuck. I tried taking it to 2700mhz and it wouldn't boot. Temps are all still good, only reading a 2 degree average increase @ 2604mhz. What could can I do to push her further?
 

·
In & out... very busy
Joined
·
1,877 Posts
Discussion Starter · #5 ·
Bios settings are as follows...
FSB: 325mhz
Ratio: 8
overall: 2600
DDR freq: 812
VOLTAGES:
CPU 1.358
Mem 1.9
NB 1.275
FSB 1.258
I/O Power 1.5
SB Core 1.05

This being AMI Bios. My Mobo is an MSI P31 neo (v1.0). Also, I would like to know if I can run this RAM...

General Information :
DIMM0 (BANK0 ) : 2048 MB - DIMM
DIMM2 (BANK2 ) : 2048 MB - DIMM

Information SPD EEPROM (DIMM0) :
Manufacturer : Transcend Information
Part Number : JM800QLU-2G
Serial Number : Unspecified
Type : DDR2-SDRAM PC2-6400 (399 MHz) - [DDR2-800]
Format : Regular UDIMM (133.35 x 3)
Size : 2048 MB (2 ranks, 8 banks)
Module Buffered : No
Module Registered : No
Module SLi Ready (EPP) : No
Width : 64-bit
Error Correction Capability : No
Max. Burst Length : 8
Refresh : Reduced (.5x)7.8 µs, Self Refresh
Voltage : SSTL 1.8v
Prefetch Buffer : 4-bit
Manufacture : Week 8 of 2008
Supported Frequencies : 200 MHz, 266 MHz, 400 MHz
CAS Latency (tCL) : 3 clocks @200 MHz, 4 clocks @266 MHz, 5 clocks @400 MHz
RAS to CAS (tRCD) : 3 clocks @200 MHz, 4 clocks @266 MHz, 5 clocks @400 MHz
RAS Precharge (tRP) : 3 clocks @200 MHz, 4 clocks @266 MHz, 5 clocks @400 MHz
Cycle Time (tRAS) : 9 clocks @200 MHz, 12 clocks @266 MHz, 18 clocks @400 MHz
Min TRC : 12 clocks @200 MHz, 16 clocks @266 MHz, 23 clocks @400 MHz

In dual mode (at the moment they are both in seperate colour slots)
Thanks folks.
 
1 - 5 of 5 Posts
Status
Not open for further replies.
Top