Tech Support banner

Status
Not open for further replies.
1 - 2 of 2 Posts

·
Registered
Joined
·
47 Posts
Discussion Starter #1
I have the most current Nero 6 updates and have most current firmware for MADDOG MD16XDVD9A2 drive. It seems the writer fails on the first try of every disk I try to either copy of make from my hard drive. It fails on DVD and on CDs. If I try more than one time, it usually works on the second attempt. Here is the error log:

David

1A23-0609-9130-2363-7106-0686

Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Ahead\Nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 10/26/2004 6:35:34 PM
Nero Version: 6.6.0.16
Internal Version: 6, 6, 0, 16b
(Nero Express)
Recorder: <MAD DOG MD-16XDVD9A2> Version: 1.F3 - HA 2 TA 0 - 6.6.0.16
Adapter driver: <> HA 2
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <MAD DOG MD-16XDVD9A2 >Version: 1.F3 - HA 2 TA 0 - 6.6.0.16
Adapter driver: <> HA 2

=== Scsi-Device-Map ===
DiskPeripheral : WDC WD1600AB-22DYA0 nvatabus Port 0 ID 0 DMA: Off
CdRomPeripheral : OEM CD-ROM F564E nvatabus Port 0 ID 2 DMA: Off
CdRomPeripheral : _NEC DVD_RW ND-1300A nvatabus Port 0 ID 3 DMA: Off

=== CDRom-Device-Map ===
OEM CD-ROM F564E F: CDRom0
_NEC DVD_RW ND-1300A E: CDRom1
MAD DOG MD-16XDVD9A2 Q: CDRom2
=======================

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 959MB (982512kB)
Free physical memory: 546MB (559604kB)
Memory in use : 43 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

18.9.2005
===== Disc-Copy over image - 1st step : Copy to image ...

9:07:15 AM #1 Text 0 File Reader.cpp, Line 127
Reader running

9:07:15 AM #2 Phase 48 File dlgbrnst.cpp, Line 1832
Analyzing disc

9:07:15 AM #3 Text 0 File Writer.cpp, Line 122
Writer Image Recorder running

9:07:15 AM #4 CDCOPY -1 File CDCopy.cpp, Line 1912
The CD is copyrighted

9:07:15 AM #5 Text 0 File CDCopy.cpp, Line 2128
_Index0_ _______Index1_______ PostPause ___LastBlockOfTrack_
Track 1: 0 0 ( 0:02.00) 312418 312417 ( 69:27.42)

9:07:15 AM #6 Text 0 File CDCopy.cpp, Line 840
Copy options: copy on-the-fly: ON
read ISRC/MCN: OFF
use jitter correction: OFF
data options
ignore read error: ON write defekt blocks OFF
read raw data: OFF read r-w subchannel data: OFF
audio options
ignore read error: ON
read indexes: OFF read r-w subchannel data: OFF
source disc does not look like CD Extra
01. 0 - 312418 = 312418, data (TRM_DATA_MODE2_FORM1_NOSUB, block size 2048)

9:07:15 AM #7 Text 0 File Burncd.cpp, Line 3233
Turn on Disc-At-Once, using CD-R/RW media

9:07:15 AM #8 Text 0 File DlgWaitCD.cpp, Line 270
Last possible write address on media: 445499 ( 99:01.74)
Last address to be written: 312417 ( 69:27.42)

9:07:15 AM #9 Text 0 File DlgWaitCD.cpp, Line 282
Write in overburning mode: NO (enabled: CD)

9:07:15 AM #10 Text 0 File DlgWaitCD.cpp, Line 448
>>> Protocol of DlgWaitCD activities: <<<
=========================================

9:07:15 AM #11 Text 0 File ThreadedTransferInterface.cpp, Line 838
Setup items (after recorder preparation)
0: TRM_DATA_MODE2_FORM1_NOSUB (1 - Data (mode 2))
2 indices, index0 (150) not provided
original disc pos #0 + 312418 (312418) = #312418/69:25.43
not relocatable, disc pos for caching/writing not required/not required, no patch infos
-> TRM_DATA_MODE2_FORM1_NOSUB, 2048, config 0, wanted index0 0 blocks, length 312418 blocks [Image Recorder]
--------------------------------------------------------------

9:07:15 AM #12 Text 0 File ThreadedTransferInterface.cpp, Line 1051
Prepare recorder [Image Recorder] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x20; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE2_FORM1_NOSUB, 2048/0x00, FilePos 0 307200 640139264, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
-150 | lead-in | 0 | 0x41 | 0x00
-150 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
312418 | lead-out | 1 | 0x41 | 0x00

9:07:15 AM #13 Phase 120 File dlgbrnst.cpp, Line 1832
Creating the image for burning

9:07:15 AM #14 Text 0 File ThreadedTransferInterface.cpp, Line 2654
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0

9:10:46 AM #15 Text 0 File WriterStatus.cpp, Line 116
< Image Recorder > start writing Lead-Out at LBA 312418 (4C462h), lenght 0 blocks

9:10:46 AM #16 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

9:10:48 AM #17 Phase 121 File dlgbrnst.cpp, Line 1832
Creating Image completed successfully



===== Disc-Copy over image - 2nd step : Burn the image ...

9:10:55 AM #1 Text 0 File Burncd.cpp, Line 2948
MAD DOG MD-16XDVD9A2
Buffer underrun protection activated

9:10:56 AM #2 Text 0 File Reader.cpp, Line 127
Reader running

9:10:56 AM #3 IMAGEGEN -10 File ImageGen.cpp, Line 366
Image was written as DAO.
DAOI:
MediaCatalogNumber = ''
TocType = 0x20
Finalized = 1
First/Last Track = 1 / 1
1: ISRC = ''
Blocksize = 2048
TrackMode = 'TRM_DATA_MODE2_FORM1_NOSUB'
TrackConfig = 0x00
First/Last Index = 0 / 1
Index0FilePos = 0, Index1FilePos = 307200, NextTrackFilePos = 640139264
CUES:
0: Ctrl=0x41 Trk= 0 (0x00) Index=00 Start=954437:08.46 ( -150) RecDep=0x00
1: Ctrl=0x41 Trk= 1 (0x01) Index=00 Start=954437:08.46 ( -150) RecDep=0x00
2: Ctrl=0x41 Trk= 1 (0x01) Index=01 Start=00:00.00 ( 0) RecDep=0x00
3: Ctrl=0x41 Trk=110 (0xAA) Index=01 Start=69:25.43 ( 312418) RecDep=0x00
MTYP: Mediumtype = CD (old format) (0x1)
Image file name: <C:\Documents and Settings\David\My Documents\TempImage.nrg>

9:10:56 AM #4 Text 0 File Burncd.cpp, Line 3233
Turn on Disc-At-Once, using CD-R/RW media

9:12:30 AM #5 Text 0 File DlgWaitCD.cpp, Line 270
Last possible write address on media: 359844 ( 79:59.69)
Last address to be written: 312417 ( 69:27.42)

9:12:30 AM #6 Text 0 File DlgWaitCD.cpp, Line 282
Write in overburning mode: NO (enabled: CD)

9:12:30 AM #7 Text 0 File DlgWaitCD.cpp, Line 2483
Recorder: MAD DOG MD-16XDVD9A2;
CDR code: 00 97 15 17; OSJ entry from: Ritek Co.
ATIP Data:
Special Info [hex] 1: C0 00 90, 2: 61 0F 11 (LI 97:15.17), 3: 4F 3B 46 (LO 79:59.70)
Additional Info [hex] 1: 00 00 80 (invalid), 2: 00 00 00 (invalid), 3: 00 00 00 (invalid)

9:12:30 AM #8 Text 0 File DlgWaitCD.cpp, Line 448
>>> Protocol of DlgWaitCD activities: <<<
=========================================
Insert empty disc to write to.
(Medium in drive: Unknown. Medium required by compilation: CD-R/RW.)

9:12:30 AM #9 Text 0 File ThreadedTransferInterface.cpp, Line 838
Setup items (after recorder preparation)
0: TRM_DATA_MODE2_FORM1_NOSUB (1 - CD-ROM Mode 2/XA, Joliet)
2 indices, index0 (150) provided
original disc pos #0 + 312418 (312418) = #312418/69:25.43
not relocatable, disc pos for caching/writing not required/not required, no patch infos
-> TRM_DATA_RAW_MODE2, 2352, config 0, wanted index0 0 blocks, length 312418 blocks [MAD DOG MD-16XDVD9A2]
--------------------------------------------------------------

9:12:30 AM #10 Text 0 File ThreadedTransferInterface.cpp, Line 1051
Prepare recorder [MAD DOG MD-16XDVD9A2] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x20; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_RAW_MODE2, 2352/0x00, FilePos 0 352800 735159936, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
-150 | lead-in | 0 | 0x41 | 0x00
-150 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
312418 | lead-out | 1 | 0x41 | 0x00

9:12:30 AM #11 Phase 36 File dlgbrnst.cpp, Line 1832
Burn process started at 48x (7,200 KB/s)

9:12:30 AM #12 SCSI -1080 File Cdrdrv.cpp, Line 1180
SCSI Exec, HA 2, TA 0, LUN 0, buffer 0x03A76E00
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x02 (KEY_NOT_READY)
Sense Code: 0x3A
Sense Qual: 0x00
CDB Data: 0xAD 0x00 0x00 0x00 0x00 0x00 0x00 0xFF 0x40 0x00 0x00 0x00
Sense Data: 0x00 0x00 0x02 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x3A 0x00

9:12:30 AM #13 SCSI -1080 File Cdrdrv.cpp, Line 1180
SCSI Exec, HA 2, TA 0, LUN 0, buffer 0x03A74A00
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x02 (KEY_NOT_READY)
Sense Code: 0x3A
Sense Qual: 0x00
CDB Data: 0x51 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x20 0x00 0x00 0x00
Sense Data: 0x00 0x00 0x02 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x3A 0x00

9:12:30 AM #14 SCSI -1080 File Cdrdrv.cpp, Line 1180
SCSI Exec, HA 2, TA 0, LUN 0, buffer 0x03A76C00
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x02 (KEY_NOT_READY)
Sense Code: 0x3A
Sense Qual: 0x00
CDB Data: 0x52 0x01 0x00 0x00 0x00 0xFF 0x00 0x00 0x1C 0x00 0x00 0x00
Sense Data: 0x00 0x00 0x02 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x3A 0x00

9:12:30 AM #15 SCSI -1080 File Cdrdrv.cpp, Line 1180
SCSI Exec, HA 2, TA 0, LUN 0, buffer 0x03A76200
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x02 (KEY_NOT_READY)
Sense Code: 0x3A
Sense Qual: 0x00
CDB Data: 0x25 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
Sense Data: 0x00 0x00 0x02 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x3A 0x00

9:12:30 AM #16 Text 0 File ThreadedTransferInterface.cpp, Line 2654
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0

9:12:30 AM #17 SCSI -1080 File Cdrdrv.cpp, Line 1180
SCSI Exec, HA 2, TA 0, LUN 0, buffer 0x03A74A00
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x02 (KEY_NOT_READY)
Sense Code: 0x3A
Sense Qual: 0x00
CDB Data: 0x51 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x20 0x00 0x00 0x00
Sense Data: 0x00 0x00 0x02 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x3A 0x00

9:12:30 AM #18 SCSI -1080 File Cdrdrv.cpp, Line 1180
SCSI Exec, HA 2, TA 0, LUN 0, buffer 0x03A74A00
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x02 (KEY_NOT_READY)
Sense Code: 0x3A
Sense Qual: 0x00
CDB Data: 0x52 0x01 0x00 0x00 0x00 0xFF 0x00 0x00 0x1C 0x00 0x00 0x00
Sense Data: 0x00 0x00 0x02 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x3A 0x00

9:12:30 AM #19 CDR -1080 File ThreadedTransferInterface.cpp, Line 1741
Disc not present

9:12:30 AM #20 TRANSFER -35 File ThreadedTransferInterface.cpp, Line 1741
Invalid track info

9:12:30 AM #21 Phase 38 File dlgbrnst.cpp, Line 1832
Burn process failed at 48x (7,200 KB/s)


Existing drivers:
File 'Drivers\CDRALW2K.SYS': Ver=6.1.1.7 , size=24698 bytes, created 6/25/2003 3:18:48 AM
File 'Drivers\PXHELP20.SYS': Ver=2.02.56a, size=17168 bytes, created 11/1/2004 4:02:55 PM (Prassi/Veritas driver for win 2K)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

Any assistance would be appreciated.

davidb2989
 

·
Premium Member
Joined
·
78,003 Posts
enable dma on the drives
and part of your problem is trying to burn copyrighted disks which is illeagal and we cannot help you with this
lower your burning speed,let the program auto detect the burning speed i find that anything over 40 produces coasters
 
1 - 2 of 2 Posts
Status
Not open for further replies.
Top