Hi
As Spunk.Funk says this is almost certainly a bad sector on your hard drive.
From your event viewer logs (You have many of these errors):
Code:
Event Type: Error
Event Source: Disk
Event Category: None
Event ID: 11
Date: 04/04/2011
Time: 06:12:03 AM
User: N/A
Computer: THEBEAST
Description:
The driver detected a controller error on \Device\Harddisk2\D.
[B]AND[/B]
Event Type: Warning
Event Source: Disk
Event Category: None
Event ID: 51
Date: 01/04/2011
Time: 07:28:07 AM
User: N/A
Computer: THEBEAST
Description:
An error was detected on device \Device\Harddisk2\D during a paging operation.
From your 1 recent minidump that wasn't corrupted:
Code:
Windows XP Kernel Version 2600 (Service Pack 3) MP (2 procs) Free x86 compatible
Product: WinNt, suite: TerminalServer SingleUserTS
Built by: 2600.xpsp_sp3_gdr.101209-1647
Kernel base = 0x804d7000 PsLoadedModuleList = 0x8055d720
...............................................................................................................
Debug session time: Fri Apr 1 07:38:43.718 2011 (UTC + 2:00)
System Uptime: 0 days 2:01:47.432
BugCheck 77, {1, adacb808, 0, b4714c4c}
Probably caused by : memory_corruption ( nt!MmInPageKernelStack+176 )
KERNEL_STACK_INPAGE_ERROR (77)
The requested page of kernel data could not be read in. Caused by
bad block in paging file or disk controller error.
In the case when the first arguments is 0 or 1, the stack signature
in the kernel stack was not found. Again, bad hardware.
An I/O status of c000009c (STATUS_DEVICE_DATA_ERROR) or
C000016AL (STATUS_DISK_OPERATION_FAILED) normally indicates
the data could not be read from the disk due to a bad
block. Upon reboot autocheck will run and attempt to map out the bad
sector. If the status is C0000185 (STATUS_IO_DEVICE_ERROR) and the paging
file is on a SCSI disk device, then the cabling and termination should be
checked. See the knowledge base article on SCSI termination.
Arguments:
Arg1: 00000001, (page was retrieved from disk)
Arg2: adacb808, value found in stack where signature should be
Arg3: 00000000, 0
Arg4: b4714c4c, address of signature on kernel stack
DEFAULT_BUCKET_ID: INTEL_CPU_MICROCODE_ZERO
IMAGE_NAME: memory_corruption
FAILURE_BUCKET_ID: 0x77_1_nt!MmInPageKernelStack+176
1. You can check your hard drive for any errors.
To do this go to
Start ->
Run -> type
chkdsk c: /r -> click
Ok. When asked if you want to force a dismount say
No. When asked to schedule the check at the next startup say
Yes. Restart your PC to allow chkdsk to run.
Note you want to especially run chkdsk on the D:\ drive. However it would be a good idea to run chkdsk on all three of your drives (on all 5 of your volumes c:\, d:\, e:\, v:\ and w:\)
2. Run the hard drive diagnostic tool for your make of hard drive. A list of Hard Drive manufacturers and the links to their Diagnostics tools can be found
here. Download the ZIP file, extract the ISO and write it to CD using a program like
ImgBurn.
Once written to CD, boot your PC with the CD and run the Advanced or Extended test.
Note you have a combination of 1 Seagate and 2 Western Digital drives. Download the Seagate tool and run that on all of the drives - one by one. If there is a problem with one of the Western Digital drives that Seatools cannot fix you will have to download the Western Digital LifeGuard tool.
