Tech Support banner
Status
Not open for further replies.
1 - 14 of 14 Posts

·
Registered
Joined
·
56 Posts
Discussion Starter · #1 · (Edited)
Stop: c000021a {Fatal System Error}
The windows logon process system process terminated unexpectedly with a status of 0xc0000139 (0x00000000 0x00000000).
The system has been shutdown.


Before BSOD occured:
1. Uninstalled Eset Antivirus, and didn't reboot.
2. Installed BitDefender2010 total care and prompted reboot so i reboot.
3. After rebooting, BSOD came up.

That's all i have done before this error occured.
Now, i can't boot from CDs/DVDs.
Can't get to safemode either, shows same problem.
I'm using XP Sp3.

Any help would be greatly appreciated.
Thanks in Advance.
 

·
Registered
Joined
·
56 Posts
Discussion Starter · #2 ·
anyone? please help me!!
Thanks in advance.
 

·
TSF Team Emeritus , Microsoft Visitng Expert
Joined
·
4,279 Posts
Hello tamachan

You need to replace "winlogon.exe" with a copy from the WinXP CD

You will need an XP installation CD to replace it. Borrow one if you don`t have one

How to replace it from XP installation CD
Configure your PC to boot from CD if it isn't already set up that way. You may need to enter the BIOS to configure the PC to boot from the CD.
Enter the BIOS and set the boot order to
floppy (if present)
CDROM
Hard disk
SAVE and EXIT

Start your PC with the XP Setup CD in the drive. When you see the "Press any key to boot from CD..." prompt, do so and let the CD-based boot process begin.

When the Recovery Console option is offered ("Press R to start the Recovery Console"), do so. You may be asked which Windows installation to enter, in which case type the number of the Windows installation you wish to work on (usually "1").

When prompted, enter the Administrator's password for that Windows installation. If you did not set a password just press ENTER

At the command prompt, type
copy d:\i386\winlogon.ex_ c:\windows\system32\winlogon.exe
ENTER

Be sure to put the spaces in
After copy
After winlogon.ex_

.
 

·
Registered
Joined
·
56 Posts
Discussion Starter · #4 ·
ok, but the problem is, i don't have have anyone to borrow a cd.
and my comp. won't boot cds >.<
i'm studying how to make a bootable flash drive now.

Thanks again.
 

·
Registered
Joined
·
56 Posts
Discussion Starter · #5 ·
can i do it with hiren's bootdisk mini xp?
if yes, please tell me what i must do.

thanks.
 

·
Registered
Joined
·
56 Posts
Discussion Starter · #6 · (Edited)
Update.

Tried Hiren's BootCD, run the ERD system restore through mini windows xp and still none =\
still shows the same error :sigh:

please help me fix my problem!

Thanks
 

·
Registered
Joined
·
56 Posts
Discussion Starter · #7 ·
HELP ME PLEASE!!!!!!! :sigh:
 

·
TSF Team Emeritus , Microsoft Visitng Expert
Joined
·
4,279 Posts
You need a way to copy "winlogon.exe" from the XP installation CD.

You cannot boot from a CD and you do not have access to an XP installation CD.
The only other option I can think of is to slave your hard drive in another machine and copy the file over to c:\windows\system32.
Do you know someone who is running XP?

.
 

·
Registered
Joined
·
56 Posts
Discussion Starter · #9 · (Edited)
ok..., successfully copied winlogon.ex_ to my old winlogon.exe
but through the mini windows xp in hiren's bootcd
i ran it the cmd there like this:

x:/i386/system32>copy f:/i386/winlogon.ex_ c:/windows.0/winlogon.exe

im still receiving the same error
but the line
"0x00000139 (0x00000000 0x00000000)"
had change to
"0x0000012f (0x00000000 0x00000000)"
 

·
Registered
Joined
·
56 Posts
Discussion Starter · #10 ·
hello?
any other solutions =/
i have something important to do there before i change to windows 7

thanks.
 

·
Registered
Joined
·
56 Posts
Discussion Starter · #12 ·
"0x00000139 (0x00000000 0x00000000)"
had change to
"0x0000012f (0x00000000 0x00000000)"
hello?
regarding the one i qouted.

it returns back to
"0x00000139 (0x00000000 0x00000000)"
 

·
TSF Team Emeritus , Microsoft Visitng Expert
Joined
·
4,279 Posts
I don`t know what to suggest since you do not have an XP installation CD.

Can you not borrow one somewhere and try running a "Repair"

A repair won't lose any data, other than Service Pack (if not on CD), any Windows Updates and unsigned drivers, which will need to be re-installed afterwards.
Stay offline to do a repair and do not go online again without a firewall enabled. After repairing XP, install Service Pack (if necessary), firewall and then you must install all Critical Updates next.

How to Repair XP.
1.Boot the computer from your Windows XP CD.

2.When you see the "Welcome To Setup" screen press [Enter] to start the Windows Setup.

Note: Do not choose "To repair a Windows XP installation using the Recovery Console, press R", you Do Not want to load Recovery Console.

3.Accept the Licence Agreement and Windows will search for existing Windows installations.

4.Select the XP installation you want to repair from the list and press [R] to start the repair. Setup will copy the necessary files to the hard drive and reboot.

5.Do not press any key to boot from CD when the message appears. Setup will then continue as if it were doing a clean install, but your applications and settings will remain intact.

http://www.theeldergeek.com/repairing_windows_xp.htm
Scroll way down page to
Windows Installation CD - Repair Current Installation

http://michaelstevenstech.com/XPrepairinstall.htm

.
 

·
Registered
Joined
·
56 Posts
Discussion Starter · #14 ·
thanks, btw, my original installation is OEM
can i repair using a retail disk i just recently borrowed?

thanks again, i'll try it when i get home :D
 
1 - 14 of 14 Posts
Status
Not open for further replies.
Top