Tech Support Forum banner
Status
Not open for further replies.
1 - 9 of 9 Posts

·
Registered
Joined
·
4 Posts
Discussion Starter · #1 ·
I got a new video card cause my on board one couldn't even run WOW. This was cheap and would fit in my computer and I thought i met the specs...However I installed, updated drivers..and i have red lines all through myscreen....onboard card was disabled..same problem...I have no idea what to do now..switched monitors as well..bad card maybe?


Operating System Microsoft Windows XP Professional
OS Service Pack Service Pack 2
DirectX 4.09.00.0904 (DirectX 9.0c)

Motherboard
CPU Type Intel Celeron, 2500 MHz (25 x 100)
Motherboard Name Unknown
Motherboard Chipset VIA P4M800 Pro
System Memory 768 MB
BIOS Type Award (06/08/06)
Communication Port Communications Port (COM1)
Communication Port Printer Port (LPT1)

Display
Video Adapter ATI Radeon X1050 Secondary (256 MB)
Video Adapter ATI Radeon X1050 (256 MB)
3D Accelerator ATI Radeon 9600 XT (RV360)
 

·
Registered
Joined
·
4 Posts
Post the make and model pc , or the make and model motherboard. Your running a 9600 AND a x1050?
No i'm not..I don't know why that came up..I did everest n it said that..I was confused my self..

This was a built computer..so I'm not positive whats in it..

For motherboard in everest this is what comes up..

Field Value
Motherboard Properties
Motherboard ID 06/08/2006-P4M800CE-8237-6A7L6B09C-00
Motherboard Name Unknown

Front Side Bus Properties
Bus Type Intel NetBurst
Bus Width 64-bit
Real Clock 100 MHz (QDR)
Effective Clock 400 MHz
Bandwidth 3200 MB/s

Memory Bus Properties
Bus Type DDR SDRAM
Bus Width 64-bit

what are you running
video card
cpu
m/board
ram
power supply
brand
wattage

check the listings in the bios for voltages and temperatures and post them

see if this list the m/b

http://www.cpuid.com/pcwizard.php

i know the basic details 2.51GHZ, 768 RAM, 350W power supply...it's a built computer..not sure on motherboard make...video card is ATI radeon x1050...ill try to get MB details

Hardware Monitoring : ITE IT8705F
Voltage CPU : 1.53 V
DIMM : 1.58 V
+3.3V Voltage : 3.22 V
+5V Voltage : 5.04 V
+12V Voltage : 10.59 V
Processor Fan : 4687 rpm
Chassis Fan : 2556 rpm
Processor Temperature : 16 °C
Mainboard Temperature : 22 °C
Power/Aux Temperature : 5 °C
ACPI Thermal Zone : 22 °C
:
Hard Disk Monitoring : S.M.A.R.T
Hard Disk Maxtor 6Y080L0 : 36 °C

my temps

Mainboard : Unspecified P4M800CE-8237
Chipset : VIA P4M800CE
Processor : Intel Celeron @ 2500 MHz
Physical Memory : 768 MB
Video Card : ATI Radeon X1050
Hard Disk : Maxtor (82 GB)
DVD-Rom Drive : SONY DVD-ROM DDU1611
DVD-Rom Drive : ATAPI DVD DD 2X16X4X16
Monitor Type : VW22LHDTV10T - 22 inches
Network Card : VT82C570 MV IDE Controller VT6102 Rhine II Fast Ethernet Adapter
Operating System : Microsoft Windows XP Professional 5.01.2600 Service Pack 2
DirectX : Version 9.0c
 

·
Registered
Joined
·
4 Posts
Discussion Starter · #6 ·

·
Registered
Joined
·
4 Posts
Discussion Starter · #8 ·
Hardware Monitoring : ITE IT8705F
Voltage CPU : 1.52 V
DIMM : 1.58 V
+3.3V Voltage : 3.34 V
+5V Voltage : 5.18 V
+12V Voltage : 10.59 V
Processor Fan : 4687 rpm
Chassis Fan : 2518 rpm
Processor Temperature : 16 °C
Mainboard Temperature : 17 °C
Power/Aux Temperature : 3 °C
ACPI Thermal Zone : 17 °C
:
Hard Disk Monitoring : S.M.A.R.T
Hard Disk Maxtor 6Y080L0 : 27 °C


now has a 500W power supply...same issue...it will be alright for 5-10 mins..then the redlines come all over the screen...I don't know what else to do with the issue...is it the card, drivers? any suggestions?
 
1 - 9 of 9 Posts
Status
Not open for further replies.
Top