XcELR8

Hello all.Im having a bit of an issue with a PC I just built and was hoping someone in here could help me out and I thank everyone in advance.The PC restarts at random,I see a quick flash of the blue screen and the PC restarts,after the reboot I send the Error report and the info I get back is Windows Stop Error,A Device Driver Has Caused The Problem.I have updated all the drivers and I am still having the issue.The only thing I have done is overclock the CPU,I set it back to default and the issue is still there.I am Running Duel Videocards SLI mode,tried running a single card,no luck.Another thing The PC boots up very slow It hangs on the Motherboard Logo screen for at least a minute +,goes to blank black screen with little flashing line in upper left corner,hangs there another 30 sec or so,then finally to the windows screen and from there is very quick.Any help anyone could offer would be greatly appreciated....Thanx again in advance.

Asus M2N SLI Deluxe Mobo AM2 Socket
AMD Athlon X2 4600+
1 Gig Dual Channel OCZ DDR2 800 Mhz Memory
Dual 7300 GT OC Nividia Videocards SLI Mode
Power Supply-Silencer 750 Quad
Western Digital 120 Gig HD-IDE

dai

turn off the auto reboot so the computer freezes on the bsod and then post the error message in full
c/panel/system/advanced/startup and recovery settings
untick the auto reboot box

XcELR8

Thank you for the info and the quick reply dai.I have turned off the auto restart,the moment it does it again I will post the error.Thanks again.

XcELR8

Hello again.This was the error on the screen.

A problem has been detected and windows was shut down to prevent damage to your computer.

DRIVER_IRQL_NOT_LESS_OR_EQUAL

Thanks.

dai

you need tro post the full message
the numers
especially the insigificant bit at the bottom left this usually pin points the problem

XcELR8

Darn I was wondering if I should have done that.Ill be sure to get all the info in next post.Thank you.

XcELR8

Hello again,I apologise I didnt post sooner but the comp just did it again lastnight for the first time in weeks,thought I got lucky and it went away.Below is the info.

A problem has been detected and windows has been shut down to prevent damage to your computer.

Technical Info.

***Stop: 0x000000D1 (0x000004B3,0x00000005,0x00000000,0xF73155ED)


*** atapi.sys-Address F73155ED base at F7310000,Date Stamp 41107b4d

Again any help would be greatly appreciated and I thank you in advance.

dai

http://support.microsoft.com/kb/817472
if you have Daemon Tools installed uninstall it

XcELR8

Hi,no I dont have Daemon Tools installed in the comp.....Thanks.

XcELR8

Hello again,I dont know if this makes a difference but the stop error seems to occur while im backing up DVDs with DVD shrink,I was backing up DVDs lastnight and it happen 3 times inside of a half hour,it has been a few weeks since I have been doing any backing up of DVDs and the problem didnt occur.It has done it when not copying dvds but it seems to do it more so when I am.This Mobo only has one IDE connector and I have the HD and CD rom running on the same IDE,at first I had the jumper settings wrong but that was only causing a very slow boot,but I have fixed that,not sure if this would have anything to do with it but thought I would throw it out there cause ya never know.Hope this bit of info is more helpful and again I cant thank you eneough for your help.....Thanks again.

XcELR8

Hello again,today a new stop error.A problem has been detected and windows has been shut down to prevent damage to your computer.

***Stop:0x000000D1 (0x50706A62,0x00000005,0x00000000,0xF73126C6)

***atapi.sys-Address F73126C6 base at F7310000,Date Stamp 41107b4d

Again I appreciate all your help.

dai

are you using an 80 wire cable on the dvd drive and have you tried burning at a slower speed

XcELR8

Hello dai,yes I am using an 80 wire cable,havent tried reducing my burn speed though so I will try that today and let you know what happens.Thanks again for your help.

XcELR8

Hello dai,I have reduced my burn speed and changed cables,I did not have the 80 wire,I was told it was but I looked into it and it was not,I now have a new cable and so far so good I have not had the stop error message.I did a buch of copying last night and no probs so far.I thank you again for your help.

dai

nice easy fix

XcELR8

Hello dai,sorry problem not solved I received another stop error today.

***Stop 0x000000D1 (0x000000AC,0x00000005,0x00000000,0xF73155ED)

***atapi.sys-Address F73155ED base at F7310000,Date Stamp 41107b4d

I was warned not to use Asus boards,should I have listened?

Thanks again for your help.

dai

cannot match up the code the AC seems to relate to a pci card causing the problem
reseat any you have
try it by removing one at a time to see if the error disappears
run memtest on the ram one stick at a time
http://www.memtest86.com/
i use asus boards and never had a problem with them

XcELR8

Hello dai,I ran memtest and no probs with the memory,I pulled my video card out and reseated it,the TV capture card I just removed it,I dont use it anymore,I never really liked the way the capture card fit my boards anyways.So I will see how it goes from here.Thanks again for your help.

XcELR8

Hello dai.well so far so good,since ive done the above no more stop errors so far,Ive been giving the comp a major work out and is working great so far.I cant thank you eneough for your help.This site rocks,great help,quick replies,cant ask for better than that.....Thanks so much again for your time and all your help.

dai

good i will mark it resolved,if the problem reoccurs post back to this thread