Tech Support Forum banner
Status
Not open for further replies.

IE browser problems?

1.4K views 11 replies 2 participants last post by  Go The Power  
#1 ·
I was curious what what kind of problem I am having when browsing and or surfing the web using IE.... A message seems to always be on the webpage. Please see statment below.
(Internet Explorer cannot display the webpage

Most likely causes:
You are not connected to the Internet.
The website is encountering problems.
There might be a typing error in the address.

What you can try:
Diagnose Connection Problems)
 
#3 ·
Hello Go The Power,,

This message varies on different webpages. Sometimes leftside sometimes rightside and sometimes just partially showing as there is no space on certain websights to show the whole message.
I just had my computer cleaned in Hijackthis log forum and it seems that after puting a firewall on and spybot that I started getting this message. Tetonbob , who helped me in that forum stated that I should put my Comodo firewall on learning mode and that it might correct it if not that I could just go back and use the windows microsoft firewall and that it should be okay. I did take the Comodo firewall off my computer and went back to the original microsoft firewall and it still shows message. Im not sure how to post a screenshot of this message but if you tell me I could post it .
 
#4 ·
Hello again cricket4462 :wave:,

To post a screen shot please follow these steps....

How to take a screen shot.


  • Open up the web page that has the problem on it.
  • Look on your keyboard and there should be a button (usually in the top right corner) that reads PrtSc, press that button.

** Please Note: If you cant find the button, here is a picture of a basic keyboard, and look at the key with the red squares around it. Click
Here (Click on the Blue link) to view the Picture. **


  • Once the PrtSc button is pressed, Open up Microsoft Paint.
  1. Click Start,
  2. Click Run
  3. Type in MSpaint,
  4. Press Ok.

  • Once Paint is open, On the Menu bar click on Edit
  • Then Paste.
  • Save the file to your computer as a Jpeg image (Mainly so the size is not so big)
On the menu bar click File,
Click Save as..
Next to Save as type click the drop arrow, and choose Jpeg
The click Save.

How to Attach a file to a post

In your nest post click on the little paperclip, as seen in the picture below:
Image


Now you should have a pop up window.
  • Click Browse
  • Find the file click on it, and press Open.
  • Press upload. When the upload is complete you can close the Upload Window, and finish typing your reply, then when done just click Submit reply.
 
#6 · (Edited)
Hello cricket4462,

Thanks for the screen shots.

From what I can see they are Add's that are being blocked, I reckon that they are being blocked either by IE-Spyad or MVPS HOST File.

I just checked (As I also use Comodo Firewall and both IE-Spyad and MVPS HOST File) and while I was using IE I got the same problems.

BTW I usually use Firefox because I dont like Internet Explorer :grin:
 
#9 ·
I swithced to firefox and must say that it is so much faster and hopefully much safer than Internet Explorer. I must say that also useing Firefox I do get another message that says (Unable to connect ect.) when browsing. I sure wish that I knew what was causing this message. I uninstalled Comodo firewall and also Spybot and still have this problem. Is there someone or somewhere you can advise me to post my problem?

Thanks, cricket4462
 
#10 ·
Sorry I am not sure were else you could post this. The problem is that when you get that message adds are being blocked which is a good thing, i know the error can be annoying but it is for a good purpose. The problem is not with Comodo or Spybot (I dont think), so please install them again.
 
Status
Not open for further replies.
You have insufficient privileges to reply here.