linderman

try manually setting these and let me know how it goes .......we can tweak upwards after you get these proven stable

JumperFree Configuration Settings:

AI Overclock tuner: Manual
CPU Ratio Setting: 9

FSB Strap to North Bridge: Auto
(333 recommended, 400 can be used too)

FSB Frequency: 333
PCI-E Frequency: 100
DRAM Frequency: DDR2-1066
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual

1st Information :

CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: 55
Write Recovery Time: AUTO
Read to Precharge Time: AUTO

2nd Information :

READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO

3rd Information :

WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: Disabled
MEM. OC Charger: Enabled
AI Clock Twister: Auto
AI Transaction Booster: Auto
Common Performance Level [10] If I set previous to manual this one is at 5
Pull-In of CHA PH1: DISABLED
Pull-In of CHA PH2: DISABLED
Pull-In of CHA PH3: DISABLED
Pull-In of CHA PH4: DISABLED
Pull-In of CHB PH1: DISABLED
Pull-In of CHB PH2: DISABLED
Pull-In of CHB PH3: DISABLED
Pull-In of CHB PH4: DISABLED

CPU Voltage: 1.20 (max 1.3625)
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.50 (2 templates used it like this) (min 1.4)(max 1.56)
FSB Termination Voltage: AUTO (possibly 1.3)
DRAM Voltage: 2.1 (By RAM Manufacturer – P5Q Board overvolts by 0.08 avg)

NB Voltage: 1.1 – 1.20. (up to 1.30 for a 4ghz overclock)
can be [AUTO] if the FSB is below 400MHz, rising to 1.3V for 400-500MHz and a maximum of 1.4V for 500MHz and above (quote: Intel)

NB GTL Reference: AUTO

SBridge Voltage: 1.20
Controls HDD, LAN, Audio etc. go up to 1.3V

PCIE SATA Voltage: 1.50

Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Auto (possilbly 400?)
NB Clock Skew : Auto (possibly 100?)
CPU Margin Enhancement: Optimized

Advance CPU Settings
CPU Ratio Setting: 9
CPU VID: Default Don't have this option
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Disabled
Vanderpool Technology: Disabled (dont have this either)
CPU TM Function: Enabled
Execute Disable Bit: Enabled



I'm going to start at those voltages and check they run 24/7 stable.

If they do i'm going to start slowing tweeking them up to a 4ghz overclock